LM339 RELAY DRIVER

Powered by Word Press. Tommy, Before you go to all that trouble, take kjennejohn’s advice and replace the 10K pullup on the comparator with something smaller. Basically I want to interrupt a power supply electronic switch. Welcome to our site! I found what looks like is going to be an excellent site: WhatRoughBeast oh jeez, you are right.

Uploader: Akikree
Date Added: 8 August 2009
File Size: 56.6 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 89474
Price: Free* [*Free Regsitration Required]

I’m guessing a capacitor somewhere would help, but I’m new to comparators.

To participate you need to register. It is either 2. To compensate this behavior we could apply a small amount of voltage feedback to the non-inverting input as shown on this following schema:.

Comparator Circuits Examples Tutorial

There’s no reason that a single 2N shouldn’t be able to sink enough current to turn on your relay. This time I will take advantage of the internal reference voltage on the non-inverting input and connect the comparator inverting input to the LDR and trimport. Home Questions Tags Users Unanswered.

Looks like I am ready to etch a board here if this new design works.

Working with the Comparator Circuit | ermicroblog

A typical one has more output current but you get whatever they have and it might be minimum. You would have to swap your inputs and use the inverting side.

It has two input wires say a DC battery for examplefrom some circuit referred to as B, which rely a input voltage source to A. The voltage on the – side of the comparator just needs to be above 2. The input voltage,into A, can range from between 0 to 6 volts.

  BIZCARD FINDER DRIVER DOWNLOAD

Quote of the day. Also–“Audioguru”can you recommend a different Comparator that may better handle this current? I would use a pull-up resistor at the base of the transistor, maybe 1K Lj339 Links Categories Recent Discussions.

First, using the formula for parallel resistors, we calculate the effective resistance of RT1 and R2 as about ohms. Nov 23, 8, 6, Therefore using this formula, we could calculate the frequency of the LED blinker circuit above as follow:.

On our next experiment we will build the light sensor circuit with the LDR light dependent resistor as the sensor and using the limit window comparator circuit. lm39

LM Quad Voltage Comparator IC Design Kit (#) | NightFire Electronics LLC

Today the modern comparator is easily found in the form re,ay integrated circuit such as the popular National Semiconductor LM quad four comparator 14 pins dual in line DIL package bellow: And these relays can be had with spike suppression diodes built in.

Here I used a 4N25 opto-coupler to drive a low power relya or horn – the current capacity of the comparator output is low while the opto-coupler is much higher. Use say a 4. Do you have a part number for the thermistor?

  DELL ADAPTEC AFW-2100 DRIVER

Will some good Samaritan delay give me a simple circuit diagram using LM or LP for temperature control of an incubator chicken — the voltage used is 12V dc — the incubator heater to be connected thru a DPDT switch.

Therefore using this formula, we could calculate the frequency of the LED blinker circuit above as follow: The junction will work as an AND gate. Power supply is 7VDC. I am only working off the “output” signal from the main computer going to the fuel pump computer.

lm339 “open collector” question…

The LM is open-collector and will need proper biasing that a series resistor will not give. The simplest circuit would be to connect it as an emitter follower, with the LED and series resistor on the emitter positive side. The diode will absorb this spike. KyranF 5, 8 Help identifying strange capacitor terminal style Started by Killians Yesterday at Today the modern comparator is easily found in the form of integrated circuit such as the popular National Semiconductor LM quad four comparator 14 pins dual in line DIL package bellow:.